First Alert FA148CP User Manual download pdf (Page 4)

–

NOTE:

Entry of a number other than one specified will give unpredictable results.

For fields *43 thru *46:

Enter 0–9; #+11 for B; #+12 for C; #+13 for D; #+14 for E; #+15 for F. Enter

[

✱

]

as the fourth digit if a 3-digit account number (for 3+1 dialer

reporting format) is used. Enter 0 as the first digit of a 4-digit account number for Nos. 0000-0999. Exit field by pressing

✱

if only 3 digits are used. E.g., For Acct.

B234

, enter:

#+11| 2 | 3 | 4

✱

PARTITION 1 PRIMARY ACCT. No.

| | | / | | | | |

Enter 4 or 10 digits, depending on selection in *48 Report

Format. See box above. To clear entries, press

[FFFF]

✱

PART. 1 SECONDARY ACCT. No.

| | | / | | | | |

Enter 4 or 10 digits, depending on selection in *48 Report

Format. See box above. To clear entries, press

. [FFFF]

✱

PARTITION 2 PRIMARY ACCT. No.

| | | / | | | | |

Enter 4 or 10 digits, depending on selection in *48 Report

Format. See box above. To clear entries, press

. [FFFF]

✱

PARTITION 2 SECONDARY ACCT.

No.

| | | / | | | | |

Enter 4 or 10 digits, depending on selection in *48 Report

Format. See box above. To clear entries, press

. [FFFF]

✱

PHONE SYSTEM SELECT

[1]

If Cent. Sta.

IS NOT

on a WATS line: 0=Pulse; 1=Tone;

if Cent. Sta.

a WATS line: 2 = Pulse; 3 = Tone

✱

REPORT FORMAT

[77]

primary secondary

0 = 3+1, 4+1 ADEMCO L/S STANDARD

1 = 3+1, 4+1 RADIONICS STANDARD

2 = 4+2 ADEMCO L/S STANDARD

3 = 4+2 RADIONICS STANDARD

5 = 10-digit ADEMCO CONTACT ID® REPORTING

6 = 4+2 ADEMCO EXPRESS

7 = 4-digit ADEMCO CONTACT ID® REPORTING

8 = 3+1, 4+1 ADEMCO L/S EXPANDED

9 = 3+1, 4+1 RADIONICS EXPANDED

✱

SPLIT/DUAL REPORTING

[0]

0 = Standard/backup reporting only (all to primary)

Primary Phone No.

2nd Phone No.

1 = Alarms, Restore, Cancel Others

2 = All except Open/Close, Test Open/Close, Test

3 = Alarms, Restore, Cancel All

4 = All except Open/Close, Test All

5 = All All

✱

BURGLARY DIALER DELAY

[2]

0 = no delay UL: must be “0”

1 = 15 seconds SIA Installations: delay

2 = 30 seconds must be minimum of

3 = 45 seconds 30 seconds

✱

SESCOA/RADIONICS SELECT

[0]

0 = Radionics (0-9, B-F)

1 = SESCOA (0-9 only reporting)

Select “0” for all other formats.

✱

DYNAMIC SIGNALING DELAY

[0]

Select delay from 0 to 225 secs, in 15-sec increments.

0 = no delay (both signals sent), 1 = 15 secs,

2 = 30 secs, etc.

UL: Grade AA must be “0;” Grade A must be “15” max

✱

DYNAMIC SIGNALING PRIORITY

[0]

0 = Primary Dialer first; 1 = Long Range Radio first.

For UL Commercial Burglary installations that use a

DACT and LRR, this field must be “0”.

✱

56, *57, *58

MENU MODES

These are Menu Mode commands, not data fields, for Zone Programming, Function

Key Programming, and Expert Mode Zone Programming respectively. See page 2 and

their respective sections in the Installation and Setup Guide for procedures.

TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (

✱

59 thru *68, *70 thru

✱

76, and

✱

89):

For 3+1 or 4+1 Standard Format:

Enter a code in the

first

box: 1–9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F.

A 0 (

not

#+10) in the

first

box will disable a report. A 0 (

not

#+10) in the

second

box will result in automatic advance to the next field.

For Expanded or 4+2 Format:

Enter codes in

both

boxes (1st and 2nd digits) for 1–9, 0, or B–F, as described above.

A 0 (

not

#+10) in the

second

box will eliminate the expanded message for that report. A 0 (

not

#+10) in

both

boxes will disable the report.

For Ademco Contact ID® Reporting:

Enter any digit (other than 0) in the

first

box, to enable zone to report (entries in the

second

boxes are ignored).

A 0 (

not

#+10) in the

first

box disables the report.

UL: see installation instructions for requirements

SYSTEM STATUS REPORT CODES (

✱

59–

✱

68)

✱

EXIT ERROR REPORT CODE

[0] See box above.

✱

TROUBLE REPORT CODE

| [00] See box above.

✱

BYPASS REPORT CODE

| [00] See box above.

✱

AC LOSS REPORT CODE

| [00] See box above.

✱

LOW BAT REPORT CODE

| [00] See box above.

✱

TEST REPORT CODE

| [00] See box above. Use Scheduling mode to set periodic test reports,

or use the following key commands:

Each mode sets schedule 32 (FA168CPS) or installer code +[#] + [0] + 0 = test report sent every 24 hours

schedule 08 (FA148CP) to the stated installer code +[#] + [0] + 1 = test report sent once per week

repeat option; first test report sent 12 hours after command. installer code +[#] + [0] + 2 = test report sent every 28 days

1 2 3 4 5 6 7 8 9 ... 15 16

Comments to this Manuals

No comments

First Alert FA148CP User Manual Page 4

Comments to this Manuals

Related products and manuals for Security access control systems First Alert FA148CP