First-alert ONELINK SCO500 User Manual download pdf (Page 2)

FIRE SAFETY TIPS

Follow safety rules and pr

event hazardous situations: 1) Use smoking

materials pr

operly. Never smoke in bed. 2) Keep matches or lighters

away from children; 3) Store flammable materials in proper containers;

4) Keep electrical appliances in good condition and don’

t overload

electrical circuits; 5) Keep stoves, barbecue grills, fireplaces and

chimneys grease- and debris-free; 6) Never leave anything cooking on

the stove unattended; 7) Keep portable heaters and open flames, like

candles, away from flammable materials;8) Don’t let rubbish accumulate.

Keep alarms clean, and test them weekly. Replace alarms immediately

if they ar

e not working properly. Smoke Alarms that do not work cannot

alert you to a fir

e. Keep at least one working fire extinguisher on every

floor, and an additional one in the kitchen. Have fire escape ladders or

other r

eliable means of escape from an upper floor in case stairs are

blocked.

BASIC SAFETY INFORMA

TION

• Dangers, Warnings, and Cautions alert you to important

operating instr

uctions or to potentially hazardous situations.

Pay special attention to these items.

•

This Smoke/CO Alarm is approved for use in single-family

esidences.

•

This combination Smoke/Carbon Monoxide Alarm has two

separate alarms. The CO Alarm is not designed to detect fire

or any other gas. It will only indicate the pr

esence of carbon

monoxide gas at the sensor. Carbon monoxide gas may be

present in other areas. The Smoke Alarm will only indicate the

esence of smoke that reaches the sensor. The Smoke Alarm

is not designed to sense gas, heat or flames.

• This Smoke/CO Alarm cannot operate without working

batteries. Removing the batteries for any reason, or failing to

replace the batteries at the end of their service life, removes

your protection.

• NEVER ignore any alarm. See “If Your Smoke/CO Alarm

Sounds” for mor

e information on how to respond to an alarm.

Failur

e to respond can result in injury or death.

• The Silence Features are for your convenience only and will

not correct a problem. See "Using the Silence Features" for

details. Always check your home for a potential problem after

any alarm. Failure to do so can result in injury or death.

• Test this Smoke/CO Alarm once a week. If the Alarm ever fails

to test correctly, have it replaced immediately! If the Alarm is

not working properly, it cannot alert you to a problem.

• This product is intended for use in ordinary indoor locations

of family living units. It is not designed to measure CO levels

in compliance with Occupational Safety and Health

Administration (OSHA) commercial or industrial standards.

Individuals with medical conditions that may make them more

sensitive to carbon monoxide may consider using warning

devices which provide audible and visual signals for carbon

monoxide concentrations under 30 ppm. For additional

information on carbon monoxide and your medical condition

contact your physician.

STEP BY STEP GUIDE TO PROGRAMMING

THIS ALARM

FOR FIRST TIME AND WHEN CHANGING BATTERIES

Action:

1. Insert batteries (2, AA batteries).

Alar

m W

ill Say:

“Welcome, First Alert Smoke and

Carbon Monoxide Alarm.”

“No location programmed” if first

time

or “[Location, example:

“Basement”] location pr

ogrammed”

when changing batteries.

“To select location, press and hold

test button now

.”

ess & Hold Test Button if

you would like to program the

location or change the location

of the Alarm. Release button

after Alarm responds.

“T

o save location, pr

ess and hold

test button after location is heard.”

Alarm will speak list of locations

(see below).

3. After you hear the location of

where you are placing the Alarm,

Press & Hold the Test Button.

“[Location, example: “Basement”]

location saved.”

If no location is chosen:

“No location saved.”

Your Alarm has now been programmed for the location of your choice.

Available locations:

Basement Kitchen Child’s Bedroom

Living Room

Dining Room

Master Bedr

oom

Family Room No Location Guest Bedroom

Office Hallway Utility Room

NOTE: Steps 1 thr

ough 3 need to be completed within two minutes.

If mor

e than two minutes pass, the Green power LED will stop

blinking. Simply open the battery drawer of the second Alarm and

epeat steps 1 through 3.

Insert the batteries into the

battery drawer of the next

Alarm. DO NOT CLOSE THE

DRA

WER.

2. Press and hold the test

button and then close the

battery drawer.

Once you hear the unit chirp,

elease the test button.

The Green power LED will start to blink indicating the ONELINK

Alarm is waiting for pr

ogram data from one of the other setup

ONELINK

Alarms.

4. Press and hold the test button on the first Alarm, until the second

Alarm

chirps and its Gr

een power LED stops blinking. Then release

the test button.

If you have purchased the hardwired battery back-up ONELINK

Alarm, you can now connect the har

dwired Alarm by installing the

three-wire connector on the ceiling to the Alarm.

Repeat steps 1-5 for additional ONELINK

Alarms.

You have now successfully linked your new ONELINK

Alarms. To

add additional Alarms at a later time, follow steps 1 through 5.

ADDING AND LINKING ADDITIONAL ONELINK

ALARMS

WHAT YOU WILL SEE AND HEAR WITH THIS ALARM

Under Normal Operations

Voice: Silent Power/Smoke LED: Flashes Green

once a minute

Horn: Silent CO LED: Off

When Y

ou Test the Alarm

Voice: “Testing.” Horn: 3 beeps, pause, 3 beeps; Voice: “Warning,

evacuate smoke in [Location, example: “Basement”].

Evacuate.”

Smoke LED: Flashes Red in sync with the horn pattern

Horn: 4 fast beeps, pause, 4 fast beeps;

Voice: “Warning, evacuate carbon monoxide in [Location, example:

“Basement”]. Evacuate.” Pause. “Highest carbon monoxide

level was [CO level example: _0_ ppm]”.

CO LED: Flashes Red in sync with the horn pattern

If Battery Becomes Low or is Missing

Voice: “Replace battery in [Location, example “Kitchen”].” Repeated

every 5 hours

Horn: chirps once a minute

Power/Smoke LED: Flashes Green On for 2 seconds/Off for

2 seconds. Low Battery Latch is now engaged.

CO LED: Off

If Alarm is Not Operating Properly (MALFUNCTION SIGNAL)

oice:

“Detector err

or in [Location, example “Kitchen”], please see

manual” (refer to Troubleshooting Guide).

Repeated every 5 hours.

Horn: Three rapid chirps every minute

Power/Smoke LED: Flashes approximately once a minute

CO LED: Off

Alar

m Levels of CO are Detected

Voice: “Warning, evacuate carbon monoxide in [Location, example:

“Kitchen”]. Evacuate.” “

____ ppm.”

Hor

4 beeps, pause, 4 beeps, voice*

Power/Smoke LED: Of

CO LED: During Alarm: Flashes Red in sync with the horn pattern.

After Alarm: Flashes Red On for 2 seconds/Off for 2

seconds. CO Alarm Latch is now engaged.

*NOTE: If unit goes into CO alarm, the r

egular 4 beeps-brief pause

cycle will repeat for four minutes. After four minutes, the pause will

increase to one minute.

Smoke is Detected

Voice: “Warning, evacuate smoke in [Location, example: “Kitchen”].

Evacuate.”

Hor

3 beeps, pause, 3 beeps, voice

Power/Smoke LED: During Alarm: Flashes Red in sync with the

hor

n pattern. After Alarm: Flashes Red On for 2 seconds/

Off for 2 seconds. Smoke Alarm Latch is now engaged.

CO LED: Off

Smoke Alarm is Silenced

Voice: Silent

Hor

Power/Smoke LED: Flashes Red

CO LED: Off

CO Alarm is Silenced

Voice: Silent

Hor

Power/Smoke LED: Off

CO LED: Flashes Red

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

First-alert ONELINK SCO500 User Manual Page 2

Comments to this Manuals

Related products and manuals for Safety First-alert ONELINK SCO500